Facebook [External Link]Twitter [External Link]

»

Sort by:  
Per Page:  
3.5mm allen key 3.5mm allen key
This is the unusually sized 3.5mm allen key you need for most original gear and clutch cable trunnions on a Lambretta. The stainless trunnions we sell use a 3mm a...
$3.70
3mm allen key 3mm allen key
This 3mm allen key fits the MB Developements stainless cable trunnions we sell. They do not fit the oddly sized 3.5mm trunnions that were standard on Lambrettas....
$3.70
BGM drive side bearing tool BGM drive side bearing tool
A high quality BGM workshop tool designed for removing and fitting Lambretta drive side bearings (6305). It is their take on the original Innocenti workshop...
$71.96
BGM engine silentblock fitting tool BGM engine silentblock fitting tool
Complete engine mount silent block removal and installation tool. Designed to aid in the fitting of both types of engine mounts. Why risk breaking your case ...
$73.79
BGM flywheel holding tool: BGM/Varitronic BGM flywheel holding tool: BGM/Varitronic
BGM made holding tool for all BGM 12v electronic and Varitronic flywheels. One end secures to the outer hex nut on the flywheel while the other goes over the engi...
$17.99
BGM PWK carb adjustment tool BGM PWK carb adjustment tool
Handy little tool specially made to remove/install all type of screws and jets on all PWK type carburetors. This includes BGM, Keihin, Stage 6 and others....
$6.29
BGM rear hub holding tool (Vespa & Lambretta) BGM rear hub holding tool (Vespa & Lambretta)
An incredibly dynamic rear hub holding tool from BGM. Works with Vespa small frame and large frame models (9" and 10") as well as Lambretta models (10&q...
$65.99
BGM stud installation kit BGM stud installation kit
This handy tool kit from BGM allows damage-free installatio...
$25.99
Cable fourth hand tool Cable fourth hand tool
Cable fourth hand tool...
$17.99
Casa Performance crankshaft puller and oil seal drift Casa Performance crankshaft puller and oil seal drift
Dual purpose tool from Casa Performance. First, this acts as a crankshaft pulling tool on all Lambretta Series 1-3, DL/GP models. Simply place up against the driv...
$37.00
Clutch compressor tool Clutch compressor tool
Designed to safely compress your clutch while you change the clutch plates. It mounts on 2 of the crankcase side s...
$35.00
Clutch holding tool Clutch holding tool
This is a laser cut steel clutch holder, which will let you safely and easily hold your clutch assembly while you undo and tighten the clutch nut. Sometimes we ha...
$16.99
Complete original tool kit Complete original tool kit
We made this set of tools for your series 1 or later Lambretta scooter, it is the set just like the one found in Lambrettas when they were new from the factory, i...
$49.95
Complete Spanner's Manual: Third edition Complete Spanner's Manual: Third edition
Coming this summer!!! Thrid edition. The Complete Spanner’s manual is the first ever step-by-step guide to rebuilding, ...
$35.99
Conrod holding tool Conrod holding tool
This tool will work on any single cylinder engine. It is designed to rest on the base gasket face and hold your con-rod (and therefore your crank). The shape of i...
$19.99
Crankshaft flywheel side bearing inner sleeve drift Crankshaft flywheel side bearing inner sleeve drift
Crankshaft flywheel side bearing inner sleeve drift. This tool is designed to safely and easily fit the inner bearing sleeve from a flywheel bearing to the crank....
$19.95

Result Pages:  1  2  3  [Next >>]  Displaying 1 to 16 (of 46 products)